NavalKleen™ - Biormedial Formula for Bilges & Oily Waste Tanks
There has been an increasing mandate, from governmental environmental agencies,
for the installation and use of Oil-Water Separators & Interceptors
in Marine Industry. These new regulations have placed a heavy burden, both
financial & operational, on all phases of Marine Industry. NavalKleen™
can & will help to overcome many of these expenses. NavalKleen™
has the ability to significantly reduce hydrocarbon contamination in Bilges,
Oily Waste Tanks and Oil Water Separators. The added cleaning & degreasing
bio-surface agent will help to keep your facility clean & safe for all
personnel. NavalKleen™
is a blend of naturally occurring micro-organisms chosen for their ability
to metabolize hydrocarbons in Bilges, Oily Waste Tanks and Oil Water Separators.
When used in a routine maintenance program, NavalKleen™
will eliminate hydrocarbon build-up, eliminating the need to clean Bilges,
pump the Oily Waste Tank and clean the Oily Water Separator. Ask Us About
“Marine Spill Kits with NavalKleen Liquid”.
Volumes Available: 20litre Pale inc. Associated Nutrients
How To Use This Product
Recommended for All Ships using No. 2 Fuel Oil thru No. 6
Fuel Oil (Bunker C)** The treatments listed should be adjusted to specific
conditions as contaminant loads vary. For best results use in accordance
with a regular preventative maintenance schedule.
**For No. 6 Fuel Oil, NavalKleen II Kit is a more effective formulation.
WET BILGE USE
- Add 5 gallons of NavalKleen Liquid Concentrate directly to bilge
- Allow NavalKleen to degrade hydrocarbons. (Oily mixtures) Process takes
approximately 8 - 16 hours
- Transfer bilge water to Oily Wastewater Holding Tank [OWHT] as necessary
OILY WASTEWATER (SLOP) HOLDING TANK "OWHT"
- Determine one percent (1 %) of the oil content as measured from the
sight gauge or sounding tape. (For example: 500 gallons x 1% = 5 gallons)
- The 5 gallon result is the amount of NavalKleen recommended to treat
the OWHT
- Add appropriate amount of NavalKleen Liquid Concentrate to OWHT
- Agitate and aerate, if possible for 24 - 36 hours
- Transfer to OWS for normal processing
OIL WATER SEPERATOR SYSTEM CLEANING
- Secure discharge valves of OWS.
- Add approximately 2 gallons of NavalKleen Liquid Concentrate to the OWS.
- Retain in OWS for 24 hours while re-circulating in the OWS system.
- Transfer normally thru Oil Content Monitor.
PRESSURE WASHING - Including Dry Bilges
- Secure discharge valves of OWS.
- Add approximately 2 gallons of NavalKleen Liquid Concentrate to the OWS.
- Retain in OWS for 24 hours while re-circulating in the OWS system.
- Transfer normally thru Oil Content Monitor.
GENERAL USE
- Set pressure washer at 20:1 ratio and begin cleaning.
- Allow water effluent to drain or accumulate in bilge.
Applications
NavalKleen™ can be used to remediate all petroleum hydrocarbons. The following is only a partial list of the most common contaminants. Please contact SpillAway™, if you have any questions about its usage:
COMMON FUELS
|
|
COMMON LUBE & HYDRAULIC OILS
- 9250 LO6 Lube Oil Diesel - MIL-L-9000H Lube Oil, Shipboard High Output Diesel
- 2190 TEP LTL Lube Oil - MIL-L-17331H Lube Oil Steam Turbine
- MIL-L-23699- Aircraft Gas Turbine Synthetic Lubricant
- MIL-H-19457D- Hydraulic Fluid, Fire Resistant
- MIL-H-17672D- Hydraulic Fluid Petroleum
- MIL-H-5606- Hydraulic Fluid, Synthetic
- Motor Oil Automotive
- Transmission Fluid
- ANSI/SAE J1899-95
- Transformer Oil
- Mineral Oil
- Paraffin
COMMON HAZARDOUS SUBSTANCES
|
|
|