NavalKleen II™ - General Maintenance & Pollution Prevention

NavalKleenII™ has been specifically formulated for ships using No. 6 Fuel Oil - Bunker C - Marine Fuels. NavalKleenII™ is an easy to use three component bioremediation system developed for Commercial vessels with heavy contaminant loading and inefficient Oil/Water Seperator ooperation caused by the use of heavy fuel. NavalKleenII™ reduces hydrocarbon contamination in Bilges, Oily Waste Tanks, Oil Water Separators. The kit contains additional micro-organisms, nutrients and special bio-cleaners that literally “eat” hydrocarbon contamination & reduce oily waste to below OCM dischargeable limits, allowing NavalKleenII™ users to massively reduce the amount of waste oil entering their waste oil tanks and drive down charges related to hazardous waste disposal.

Volumes Available: 20litre Pale inc. Associated Nutrients

---

How To Use This Product

Recommended for All Ships using No. 2 Fuel Oil thru No. 6 Fuel Oil (Bunker C). The treatments listed should be adjusted to specific conditions as contaminant loads vary. For best results use in accordance with a regular preventative maintenance schedule.

WET BILGE USE

1. Add 5 gallons of Navalkleen II Liquid Concentrate directly to bilge.
2. Open bag # 1. Remove water soluble pack and drop into bilge
3. Open bag # 2. Pour contents into bilge.
4. Allow all NavalKleenII™ kit components to degrade hydrocarbons.
   Process takes approximately 8 - 16 hours
5. Transfer bilge water to Oily Wastewater Holding Tank [OWHT] as necessary.

OILY WASTEWATER (SLOP) HOLDING TANK "OWHT"

1. Determine one percent (1%) of the oil content as measured from the sight gauge or sounding tape.
   Example: 500 gallons x 1% = 5 gallons
   The 5 gallon result is the amount of NavalKleenII™ recommended to treat the OWHT
2. Add appropriate amount of NavalKleenII™ Liquid Concentrate to OWHT.
3. Open bag # 1. Remove water soluble pack and drop into OWHT
4. Open bag # 2. Pour contents into OWHT
5. Agitate and aerate, if possible for 24 - 36 hours.
6. Transfer to OWS for normal processing.

---

Applications

NavalKleenII™ can be used to remediate all petroleum hydrocarbons. The following is only a partial list of the most common contaminants. Please contact SpillAway™ if you have any questions about its usage:

COMMON FUELS

JP-5/JP-8 Standard - MIL-T-5624P Aviation Turbine Fuel Burner Fuel Oil - ASTM D396 STD Spec Fuel Oil Naval Distillate Fuel NDF - MIL-F-16884H Diesel Fuel Marine(DFM) JP-8 Aviation Turbine NO 2. Diesel Fuel NO. 6 Diesel Fuel NO 2. Diesel Fuel DF-1 Low Temp JP-4 Jet Fuel

JP-5 Jet Fuel JP-7 Jet Fuel DF-2 General F-44 (JP-5) F-76 Diesel Kerosene Gasoline Bunker C NPD MGO AVGas

COMMON LUBE & HYDRAULIC OILS

• 9250 LO6 Lube Oil Diesel - MIL-L-9000H Lube Oil, Shipboard High Output Diesel
• 2190 TEP LTL Lube Oil - MIL-L-17331H Lube Oil Steam Turbine
• MIL-L-23699- Aircraft Gas Turbine Synthetic Lubricant
• MIL-H-19457D- Hydraulic Fluid, Fire Resistant
• MIL-H-17672D- Hydraulic Fluid Petroleum
• MIL-H-5606- Hydraulic Fluid, Synthetic
• Motor Oil Automotive
• Transmission Fluid
• ANSI/SAE J1899-95
• Transformer Oil
• Mineral Oil
• Paraffin

COMMON HAZARDOUS SUBSTANCES

Ethylene Glycol Glycolethers Ketone Solvents Acetone Methyl Alcohol Isopropyl Alcohol

Mineral Spirits Benzene Napthalene N-Hexane Paint Thinner Petroleum Distillates

Stoddard Solvent (PD-860) Ethylbenzene Organic Pesticides Toluene Turco Solvent Xylene